统一全部产品为
2输入特性(input characteristics):
2.1输入电压(input voltage):
额定电压(nominal voltage):100-240vac
调整范围(variation range):90-264vac
2.2输入频率(input frequency):
额定频率(nominal frequency):50/60hz
调整频率(variation frequency):47-63hz
2.3输入电流(input current):
当输入交流电压为额定值的下限时,输出电压负载满载,大输入交流电流0.5a。
0.5arms max at any input voltage and rated, dc output rated load.
2.4浪涌电流(inrush current):
当输出为额定负载,环境温度为25℃,输入240vac冷态起动电源时的大浪涌电流小于30a。
30amps max. cold start at 240vac input, with rated load and 25℃ambient.
2.5 ac漏电流(ac leakage current):
当输入电压240vac时,大漏电流为0.25ma。
0. 25ma max at 240vac input.
3、输出特性(output characteristics):
3.1专业充电功能
开始阶段恒流充电,led指示灯为红灯,充电到额定电压时,转为第二阶段恒压充电,电流慢慢降低,当充电电流达到0.1-0.2c电流时,led指示灯转为绿灯,此时电池已经充满到90%-95%,电池以很小电流继续充电,直到充满。
3.2充电时间计算
电池容量看电池外面的标注,充电电流看充电器标注的输入电流
a、充电电流小于等于电池容量的5%时:
充电时间(小时)=电池容量(mah)×1.6÷充电电流(ma)
b、充电电流大于电池容量的5%,小于等于10%时:
充电时间(小时)=电池容量(mah)×1.5÷充电电流(ma)
c、充电电流大于电池容量的10%,小于等于15%时:
充电时间(小时)=电池容量(mah)×1.3÷充电电流(ma
d、充电电流大于电池容量的15%,小于等于20%时:
充电时间(小时)=电池容量(mah)×1.2÷充电电流(ma)
e、充电电流大于电池容量的20%时:
充电时间(小时)=电池容量(mah)×1.1÷充电电流(ma)
3.3波纹和噪音(ripple and noise):
测试条件:任何负载正常工作下,使用示波器带宽为20mhz连接到充电器的输出端,同时输出端并连一个47uf的电解电容和一个0.1uf的瓷片电容。
the ripple and noise are as follows when measure with max. bandwidth of 20mhz and parallel 47uf/0.1uf,crossed connected at testing point.
充电器不对此项目做要求
3.4启动延迟时间(turn on delay time):
当输入115vac和输出大负载时,大启动时间为2s。
2 second max. at 115vac input and output max. load.
3.5上升时间(rise time):
当输入115vac和输出大负载时大时间为40ms。
40ms max. at 115vac input and output max. load.
3.6保持时间(hold up time):
当输入115v和输出大负载时,小保持时间为5ms。
5ms min. at 115vac input and output max. load.
3.7效率(efficiency):
当输入100vac和输出大负载时,小80%。
80%min.at 100vac input and output max. load.
当输入240vac和输出大负载时,小85%。
85%min.at 240vac input and output max. load.
3.8过冲(overshoot):
在电源开启或关闭的时候,大15%。
15%max.when power supply at turn on or turn off.
4、保护功能(protection requirement):
4.1短路电路保护:
short circuit protection:
该电源供给器在短路解除时,能恢复正常工作。
the power supply will be auto recovered when short circuit faults remove.
4.2过流保护(over current protection):
过流故障排除后,电源将自动恢复正常工作。
the power supply will be auto recovered when over current faults remove.
4.3过压保护(over voltage protection)
当输出电压超过额定电压时,电源将保护,故障排除后能恢复正常工作。
the power supply will not be auto recovered when faults remove.
5、环境要求(environmental requiremet):
5.1工作温度(operating temperature):
0℃~ -40℃,满载,正常工作(full load normal operation)。
0℃to40℃,full load normal operation.
5.2储存温度(storage temperature):
-20℃to85℃,带外壳(with package).
5.3工作湿度(relative humidity):
5%(0℃)~90%(40℃),72小时,满载,正常工作
5%(0℃)~90%(40℃)rh,72hrs,full load normal operating.
5.4振动(vibration):
1、测试标准:国际电工电子委员会 operating: iec 721-3-3 3m3
5~9hz,a=1.5mm 加速度(9~200hz,acceleration 5m/s2) 2、运输(transportation): iec 721-3-2 2m2
5-9hz,a=3.5mm
9~200hz,加速度acceleration=5m/s2
200~500hz,加速度acceleration=15m/s2
3、轴向振动(axes,10 cycles per axis).
在测试过程中不能出现性的损坏。
no permanent damage may occur during testing.
在电源开启和关闭后,样机能够恢复到初条件。
the product has to restors its original situation after power off/on.)
5.5跌落试验(dropping)(packed):
一个角,三个棱, 六个面。
1 corner,3 edges, and 6 surfaces
高度76m height:76cm
6、安全及emc要求(safety and emc requirement):
6.1安全:
6.2高压(dielectric strength):
primary to secondary):1500vac/5ma/60s.
7、结构参数(mechanical requirement):
7.1外壳(enclosure):
见规格书
7.2输入接头(input connector):
7.3;输出线
dc 线: awm 2464 18awg*2c,vw-1,80℃,ft1,300v,线上有字,总1米,
不带环,dc头为:卡(壹正贰负叁空)
8、铭牌 (label):
9、包装
每箱数量:40台
外箱尺寸:45*31*34mm
每箱重量:15kg
包装材料:pe袋子+白盒+外箱
详细介绍
深圳金正信科技有限公司其他商品